Threaded Bolt Catch Pin

Manufacturer: Shield Arms
A stainless steel threaded bolt catch pin, .530" long, for Shield Arms and Aero Precision M4E1 lowers. Threads into the receiver instead of a roll pin. Doesn’t fit mil-spec lowers.
Availability: In stock
$7.45
i h
Buy now, pay later Available at checkout on orders over $150
Compatibility

Fits SA-15, SA-9, SA-4 and Aero M4E1 Lowers.

This pin fits lower receivers with a threaded bolt catch pin hole: Shield Arms SA-15 and SA-9 folding lowers, SA-4 billet lowers and Aero Precision M4E1 lowers. It doesn't fit standard mil-spec AR-15 lowers, which hold the bolt catch with a roll pin. Not sure which you have? If your bolt catch is held in by a pin that threads into the receiver, this is the replacement.

What Is the Shield Arms Threaded Bolt Catch Pin?

It's a stainless steel pin that holds the bolt catch in an AR-15 lower built with a threaded bolt catch pin hole. It threads into the receiver with a standard hex driver instead of being driven in like a mil-spec roll pin, so the bolt catch comes out and goes back in without a punch. It's .530" long overall and fits Shield Arms SA-15, SA-9 and SA-4 lowers and Aero Precision M4E1 lowers. Made in Bigfork, Montana. Keep one as a spare for your build or use it to replace a lost or damaged pin.

  • Fits: Shield Arms SA-15, SA-9 and SA-4; Aero Precision M4E1
  • Doesn't fit: mil-spec lowers that use a roll pin
  • Material: stainless steel
  • Overall length: .530"
Bolt Catch Pin

Thread It In. No Roll Pin to Fight.

On a mil-spec lower, the bolt catch is held in by a roll pin you drive in with a punch, and starting it without scratching the receiver is one of the fiddliest steps in a lower build. Lowers with a threaded bolt catch pin skip that step: the pin threads in, and it threads back out when you want to swap the bolt catch.

It's a small part that's easy to lose on the bench or in the field. This is the same style of pin our SA-15, SA-9 and SA-4 lowers use, in stainless steel, and it also fits Aero Precision M4E1 lowers. Aero's own pin is slightly shorter; ours fits the M4E1 too.

.530" Overall length
SS Stainless steel
4 Lowers: SA-15, SA-9, SA-4, M4E1
USA Made in Bigfork, MT
Features

A Better Way to Hold the Bolt Catch

  • Threads In

    Installs with a standard hex driver, not by driving a roll pin, so there's less risk of marring the lower.

  • Comes Back Out

    Remove it to swap or service the bolt catch, then thread it back in. No punch and no roll pin holder.

  • Stainless Steel

    Made from stainless steel in Bigfork, Montana, for strength and corrosion resistance on a part that sits in the side of the receiver.

  • Four Lowers

    Fits the Shield Arms SA-15, SA-9 and SA-4 and the Aero Precision M4E1. One spare covers any of them.

Installation

Swap the Bolt Catch Without a Punch

Seat the bolt catch, its spring and plunger in the lower, line up the bolt catch with the pin hole, and thread the pin in with a standard hex driver until it's snug. To remove it, thread it back out. Don't overtighten it, and function check the bolt catch before you shoot. Step-by-step help is on our installation guides page.

Compatibility

Will It Fit My Lower?

It fits lowers built for a threaded bolt catch pin. Mil-spec lowers use a roll pin instead.

Lower Bolt Catch Held By Fits
Shield Arms SA-15 Threaded pin ✓
Shield Arms SA-9 Threaded pin ✓
Shield Arms SA-4 Threaded pin ✓
Aero Precision M4E1 lowers Threaded pin ✓
Mil-spec AR-15 lowers Roll pin —

Building on a Shield Arms lower? See our folding and non-folding lowers.

Specifications

Part Threaded bolt catch pin
Fits Shield Arms SA-15, SA-9 and SA-4 lower receivers; Aero Precision M4E1 lower receivers
Doesn't fit Mil-spec AR-15 lowers that use a bolt catch roll pin
Overall length .530"
Material Stainless steel
Install Threads into the receiver with a standard hex driver; no roll pin punch
Made in Bigfork, Montana, USA
In the package (1) threaded bolt catch pin
Warranty Lifetime warranty

Stainless Steel

Stainless steel resists corrosion and holds its threads through repeated installs, so the pin can come out and go back in whenever you service the bolt catch.

Stainless
Questions

Threaded Bolt Catch Pin FAQ

Which lowers does it fit?

Shield Arms SA-15 and SA-9 folding lowers, SA-4 billet lowers and Aero Precision M4E1 lowers, which all hold the bolt catch with a threaded pin.

Will it fit a mil-spec lower?

No. Mil-spec AR-15 lowers use a roll pin for the bolt catch and don't have a threaded hole for this pin.

Does it fit my Aero M4E1 even though it's longer?

Yes. Aero's own pin is slightly shorter, and ours, at .530" overall, fits the M4E1 lower.

Why a threaded pin instead of a roll pin?

A roll pin has to be driven in with a punch, which is easy to get wrong and can scratch the receiver. A threaded pin threads in and comes back out, so the bolt catch is easy to install and replace.

Can I reuse it?

Yes. It's built to come out and go back in when you service or swap the bolt catch.

How do I install it?

Seat the bolt catch with its spring and plunger, line it up with the pin hole and thread the pin in with a standard hex driver until snug. See our installation guides for step-by-step help.

What's covered?

It's made in Bigfork, Montana, and covered by our lifetime warranty against defects in materials and workmanship.

Firearm Transfers

Email your preferred FFL to [email protected]. Include:

  • Your name
  • Order number
  • FFL name and address
  • Copy of the FFL (if available)
Products specifications
Firearms Manufacturer Shield Arms
Firearms Model SA-15, SA-9
Installation Help

Not sure how to install this product? Our step-by-step guides and video walkthroughs make it simple.

View Installation Guides →

FREE SHIPPING FOR ORDERS OVER $100!